Tin tức:
IoT - Internet of Things
Artificial Intelligence

Kit phát triển Wifi ESP8266 V12 Development Board

    Kit phát triển Wifi ESP8266 V12 Development Board
Nhà sản xuất: Import
Mã sản phẩm:HS000597
Giá bán
59,000₫
Thêm vào giỏ hàng

Kit phát triển Wifi ESP8266 V12 Development Board bao gồm module chính Wifi SoC ESP8266 V12 và các ngoại vi đi kèm để bạn có thể dễ dàng thí nghiệm trên ESP8266, đặc biệt kit có thiết kế hộp pin giúp bạn có thể dễ dàng cấp nguồn và thí nghiệm các ứng dụng sử dụng pin cho ESP8266.

Đặc điểm nổi bật :

  • Kèm theo 1 đế 3 pin tiểu size AA.
  • Tích hợp 1 quang trở
  • Tích hợp 1 LED RGB (3 màu)
  • Ra thêm 3 chân giao tiếp UART ( TX, RX, GND).
  • Kích thước : 4.2 x 5.1 cm

Thông số kỹ thuật :

  •     Tương thích các chuẩn wifi : 802.11 b/g/n
  •     Hỗ trợ : Wi-Fi Direct (P2P), soft-AP
  •     Tích hợp TCP/IP protocol stack
  •     Tích hợp TR switch, balun, LNA, power amplifier and matching network
  •     Tích hợp bộ nhân tần số, ổn áp, DCXO and power management units
  •     +25.dBm output power in 802.11b mode
  •     Power down leakage current of <10uA
  •     Integrated low power 32-bit CPU could be used as application processor
  •     SDIO 1.1/2.0, SPI, UART
  •     STBC, 1×1 MIMO, 2×1 MIMO
  •     A-MPDU & A-MSDU aggregation & 0.4ms guard interval
  •     Wake up and transmit packets in < 2ms
  •     Dòng tiêu thụ ở Standby Mode < 1.0mW (DTIM3)

Các chẩn giao tiếp và các thông tin khác :

  •     SDIO 2.0, SPI, UART
  •     32-pin QFN package
  •     Integrated RF switch, balun, 24dBm PA, DCXO, and PMU
  •     Integrated RISC processor, on-chip memory and external memory interfaces
  •     Integrated MAC/baseband processors
  •     Quality of Service management
  •     I2S interface for high fidelity audio applications
  •     On-chip low-dropout linear regulators for all internal supplies
  •     Proprietary spurious-free clock generation architecture
  •     Integrated WEP, TKIP, AES, and WAPI engines

Tài liệu tham khảo :

Lưu ý : khi nối dây để nạp code hay flash firmware ở 3 chân nạp, chúng ta phải nối như sau ( vì mạch đã nối chéo với ESP sẵn rồi) :

ESP8266USB - UART
TXTX
RXRX
GNDGND

Cách vào các chế độ boot của ESP8266, để flash firmware chúng ta cần vào chế độ boot UART

Lưu ý : Khi cắm Jump ( màu vàng ) thì GPIO0 = LOW

MTDO

(GPIO15)

GPIO0GPIO2ModeMô tả
LLHUARTDownload code qua UART
LHHFlashBoot from SPI Flash
HxxSDIOBoot from SD-card

 

Phần mềm nạp firmware

Firmware NodeMCU mới nhất

IDE lập trình cho ESP8266 với firmware NodeMCU : ESPlorer


Bộ SDK ESP8266 IOT

SDK from Expressif

Hướng dẫn dùng với Arduino  của SeedStudio

ESP8266 diễn dàn chính thức

Arduino project Các ứng dụng mẫu kết hợp với arduino

 

Thông tin sản phẩm được Hshop.vn tự xây dựng, nếu sử dụng xin vui lòng ghi rõ nguồn, xin cảm ơn!